Tuesday, May 3, 2011

The strongest bench you'll never buy

Pulling off DIY projects like this is what makes everything worth it. When you can produce something that is so dirt cheap and yet so effective at its purpose, it just makes you feel all warm and fuzzy inside. In this project, I'll show you how to make a weight bench that is strong and incredibly cheap. This is what DIY is all about.



Cost: less than $50
Project Time: 1 day
Difficulty: You have to cut 2x4s and plywood. You have to operate a drill. For the pad you have to cut fabric and use a manual powered staple gun. In other words, not hard at all.

Tools Needed:
  • Drill
  • Saw (for cutting wood) - miter saw is best for cutting 2x4s, but you need something for long straight cuts in plywood as well (I used a normal handsaw)
  • Staple Gun - just a manual powered one, you don't need an air compressor or anything fancy like that.

Materials Needed:
  • 2x4 Studs - at 8 feet long each, you'll need 5
  • 4 Elevator Bolts (at least 1 1/2 inches long) - click here for picture
  • 4 Wingnuts to fit the elevator bolts.
  • Foam padding
  • Fabric of your choice (vinyl, leather, auto or furniture upholstery)
  • 2 1/2 inch decking screws (T-25 star head is my favorite)
  • Wood glue
  • Gorilla glue, or other similar metal/wood adhesive
  • Staples for your staple gun (check your gun for proper size)

The only person this won't be strong enough for is Bruce Banner.

Shopping for a weight bench can be difficult. And by difficult I mean expensive. And just to be clear, whenever I use the phrase "weight bench" I mean a strong one that can be used to Bench Press. The problem you'll run into when buying these is that the reasonably priced ones are not rated to hold much weight. You'll see figures like "300 lbs." But when you consider that the bench has to hold your body as well, 300 lbs. is not much. If you weigh a measly 150 lbs. when you start, and bench press 150 lbs. That's your 300 lbs. right there. This is novice level lifting.

Once you turn into a real lifter after a few years of training, you'll probably weigh closer to 200 lbs. yourself and be benching near 300 lbs. Now that's 500 lbs. and all those affordable weight benches are now too weak for your purposes. But when you start pricing quality benches that are rated for this type of serious lifting, you are going to have to pay hundreds of dollars for them. This is unacceptable by Homemade Strength standards.

The fact of the matter is you can build your own weight bench that can support a ton of weight, I literally mean a ton, that's not slang. You'll never be able to bench press even half a ton so basically what I'm telling you is that you can build a bench that will be many times stronger than you need it to be. And you can do it for less than $50.

A proper weight bench is 17 inches tall, pad included. This bench will have a plywood base that is 3/8 inch thick. It will also have a plywood top, and the removable padding has a plywood base. The total thickness of all the plywood will add up to just over an inch. The pad itself is going to be about 1/2 inch when compressed. If your pad differs from this then adjust accordingly. However, it's better to make your bench too tall rather than too short. So we're going to cut our 2x4s into 15 1/2 inch segments. To start, we will cut sixteen pieces of 2x4, each being 15 and 1/2 inches long. If you have a miter saw or at least a power saw that can handle the job (circular saw, etc.) you will enjoy the process. If you do not, this will be the first wave of a lot of hard labor cutting by hand. Thankfully, I have a miter saw.

 With sixteen boards cut to the length of 15 and 1/2 inches, we're ready to start assembling the top legs. These legs are like miniature I-beams made of three 2x4s each. It's important that you follow my directions of assembly. First step is to make a "T" out of two pieces (see diagram #1).
Mark and drill three holes through the top of the T (Board A). These three holes should be towards the middle of that 2x4, not towards the ends (see diagram #2). Read ahead if you have to, to gain more understanding of what we're doing and why. Drill all the way through Board A so that your bit goes into Board B. Then deepen the holes on Board B to prevent splitting when you put your screws in.



 Slather some wood glue along the face where the boards will touch each other. Now drive three screws into the pre drilled holes. Wipe the excess glue off and you now have one "T" piece. Repeat this procedure and make a second "T" piece.

Now we will cut the 2x4 runners that span the length of the bench. We need two. I made mine 43 inches long. I'm 5 feet 10 inches tall and this gives me plenty of room on the bench. Just make sure your bench is long enough to accommodate you from the bottom of your ass to the top of your head. If you have at least that much room, you're good to go. Whatever measurement you choose, cut two 2x4 studs to this length.


Before we attach these, we have to make holes in our top legs (T pieces) to fasten them to the runners (see diagram #3). We will drill four holes in our "T" piece; two on top, two on bottom. I recommend that you drill from the top of the T downward, as shown in diagram #3. If you drill from the bottom up, Board B will get in the way. This is how we will have to drive our screws (unavoidable) but in order to make straight holes drill from the top.

Aren't diagrams helpful?

But before we drill, we have to measure. Take one of your T pieces and measure 2 inches from the end of Board A and mark a line. Now measure 4 inches from the same end and mark a line. Now repeat these steps for the other end of Board A. You have divided the ends of your board into two sections. We'll call them "top box" and "bottom box." For this T piece choose a box, it doesn't matter which so I'll just pick "top box." Drill two holes in the top box. One centered on each side of Board B. (diagram #3). Do the same for the other end of your T piece. So this is your "top box" T piece.

Now take your other T piece and do the same thing. But this time, drill your holes in the "bottom box". The reason this is important is because these T peices will both be screwing into the same middle board and we need to make sure that you get all four screws into a small space without hitting each other. In other words, the screws on the top box board will be higher than the ones from the low box board. Marking is key to avoiding conflict when it's time to put it all together.

With four holes drilled in your T pieces, we can now attach our long runners. We're going to start with the bottom runner. The best way to mark this runner is to drive screws into your predrilled holes on the bottom of your T piece. Have them sticking out the back of the T piece just a little bit. Now, line up the T piece with the bottom runner as shown in diagram #4. The left side of your runner board should be in line with the left side of your T piece.


Use a level to ensure you're T, which is a leg of the bench, is straight up and down. Now just press the T and the runner together. Since the screw tips were slightly through the T piece they will poke into the runner board and mark it. Now you can drill on those marks, just a bit (not all the way through. Predrilling like this ensures that everything goes in the way you want it and the wood will not split. Slather the point where the boards will contact each other with wood glue. Drive in your two screws. At this point you should have one long runner on the bottom, attached to one T piece.

THE IMPORTANT BOARD STEP

This is a significant step, we're going to label this "The Important Board Step" so that you can repeat it later when I tell you to. Grab two 15 1/2 inch boards. Just like you did with the T piece, measure 2 inches from the end of the board and mark a line, then measure 4 inches and mark a line. Do that on both ends of the board. And do that for both boards. Designate one board as "top box" the other as "bottom box". Drill two holes within the proper "box" on each end of the board. Again repeat that for both boards. So each board should have four holes in it, two at one end and two at the other. And one board should have said holes in the top boxes and the other in the bottom boxes.


Take one of these boards and, just like you did with the T piece, glue it and screw it to the other end (foot end) of the bottom riser, which is already attached to one T piece at the head end.

Now repeat the procedure with the top runner. Secure it to the top of the T piece at one end and the single 2x4 at the bottom. Again use your level to make sure your legs are straight and your runner is straight as well. We're building a flat bench, not an incline or decline bench, after all. Now you should have a frame that looks as it does in diagram # 4-B



To complete this side we need two more of those 15 1/2 inch studs. We're going to cap off our T and make it an I. Just like we did when making the T, put three holes  along the length of the board, in the center as shown. Slather the contact point with wood glue and drive your three screws. Do the same exact thing with your single 2x4 at the foot, now making it a double 2x4 (in essence a 4x4). This is shown in diagram #5.
Not to scale.
From here, go back up the page, to the start, and read the directions again, this time doing it on the other side of the runners. Take the T piece that you've already made and attach it to the other side of the runners. Then take the single board you've already made for the foot of the bench and attach that to the other side of the runners. Then turn the T to an I and the single board to a double at the foot. You've now used up ten of our sixteen lengths of wood. The next step is to overkill reinforce this sucka.

The following picture will do more than words can to instruct you. It's quite straightforward, now that you've got some experience, we're not doing anything different than we've already done. We're putting three boards on each side, towards the head of the bench, where the weight and force will be when you bench press. This is where "The Important Board Step" comes in. We need 3 more pairs of boards. They have to match each other. Meaning 3 have to be "top box" and 3 have to be "bottom box". Basically just repeat the "Important Board Step" three times and you'll have three matching pairs. Secure them as the picture shows, three on each side, covering the top half of the bench (near the head).

Two is better than one, and Twelve is better than two.
No less than 12 supporting beams would have to utterly fail under the load in order for this bench to break. The rating for each beam is more than a ton. Since the average human would be absolutely ecstatic if they could manage even 1/4 that amount, I think we can safely say this bench is well beyond the strength of what you or I would ever need.

The frame of this thing is now complete. The next step is to put plywood on the bottom. The easiest way to do it is to simply put the frame onto your piece of plywood and trace around the frame. As you can see from the picture, I put a piece of plywood under the four 2x4s at the foot of the bench. I then put another piece under the six supports in the middle of the bench. Then another larger piece around the "I beam" legs at the head of the bench.

You can click these pictures to enlarge them, didn't you know?
This larger piece isn't a precise measurement. It is simply wide enough to fit the I beams, and long enough to provide support so that the bench doesn't rock side to side. It's roughly  7 inches longer than where the I-beams stop on each side. Make these measurements / tracings and then cut your plywood. Now drill and screw the plywood onto the frame, no wood glue needed. Do you best to put your screws in spots that don't already have screws in them. I trust you can use your eyes to figure that out.

For the top piece we are putting another layer of plywood. The shape of it is just an outline of the shape of the frame from the top. It's a T shape. The width of the bench is something you could vary depending on your preferences. Standard dimensions for powerlifting benches tends to be around 12 inches. I know some bigger lifters that like a much wider bench. I originally had mine wide like this, but it interfered with arms in the bottom position. My body type/size requires a smaller width, and since I'm not a competitive powerlifter, nobody will care if I make mine suited to my needs. But if you need/like a wider one than adjust accordingly.

As such, the trunk of the "T" on my bench is 9 1/2 inches wide. The top of the T is 15 1/2  by 5 inches (see picture). Cut this shape out of ply wood and screw it into the frame, again choosing places that don't already have screws in them. Also notice that i rounded the corners of this piece. I recommend you do the same to avoid potential injuries. Simply chop off the corner with a saw and then use sandpaper to round it out.

Can also be used as a diving board.
Before we upholster it, we have one last thing to do. We have to make the actual pad that you will lay on. This is composed of three parts, a plywood base, foam, and fabric. Start with the plywood base. I made mine roughly 10 inches wide. Some bigger guys like a wider pad. I'm a small guy, by my standards, and I originally had my pad wider but it was interfering with my arms at the low point of the lift. 10 inches works well for me. I can't say it will be the right size for you.

After you decide on a pad size, cut a rectangle of plywood measuring the width that you've decided on and a length that is about 2 inches longer than the top plywood piece of your frame. Measure, mark, and cut this piece out. Again, round the corners so that they don't rip the fabric you will cover it with.

Now we need to drill holes through both this newly cut plywood and the top plywood part of the frame. Center your plywood pad base on top of the plywood board on the frame so that it hands over an equal amount on all sides. Drill four holes, two towards the head of the bench and two towards the foot. The size of your holes should be just big enough to fit the shaft of your elevator bolts. The exact location of these is up to you to discover. You need the holes  go through both pieces of plywood. You need them to be  in open areas so that the frame doesn't interfere. These holes are where your elevator bolts and wignuts will be going so you need enough open space for your wingnut to thread on to the bolt.

Notice how there's plenty of room to turn the wingnuts. Choose such places when drilling your holes.

The next step is to secure your elevator bolts to the pad's plywood base. With the plywood base still centered on the frame, put your bolts into the holes. If you made your holes small enough the bolts won't sit all the way down. Elevator bolts have a slightly bigger square section towards the head. Put some Gorilla glue around the top of your bolt and hole. Now hammer the bolt into the hole. Repeat for all the bolts. Your elevator bolts need to be a minimum of 1 1/2 inches. They have to go through two pieces of 3/8" thick plywood, and have enough left over for a wingnut, which is like 1/4" at least. I personally got by with the absolute minimum bolt, it just barely fits. Apparently when I did this I miscalculated. I suggest you don't do the same. Get a longer bolt, if you can manage it, better too long than too short.

These bolts are barely long enough to work. Do as I say, not as I do.

The reason why we are doing all this is so that the pad section is removable. If you ever want to reupholster it, now you can. And we also don't want to fasten the pad by screwing up from the bottom because then we'd be getting stabbed by screws when we lie on it. You can also see why we choose something unorthodox like elevator bolts. They have a completely flat head, like a nail. So they won't create an uncomfortable bump in your pad like a rounded or hex bolt may.

The final step is to upholster this baby. You can choose whatever foam and fabric you want. Ideally heavy duty foam made for furniture or auto seats would be best. It's probably pretty expensive. I simply used a basic roll of foam that you can get at Walmart for like $15. For fabric, again upholstery fabric intended for furniture or auto seats will be of the  highest quality but is more expensive. I used cheap vinyl from Walmart. It's holding up perfectly fine after six months of training. If it ever wears out I'll upgrade to better stuff. Depending on the width of your chosen fabric, you will either need one or two yards.

First we need to put the foam onto the plywood. If you are using thin and / or soft foam you should double or triple layer it.  The foam should be just a bit larger than the dimensions of your plywood. Cut down your foam to match the size of your plywood. Lay your fabric out on the floor, so that the good side is facing down. Now lay your plywood with foam piece foam side down. So on the floor you will have your fabric, then foam layers, then plywood on top.

Look at this quality craftsmanship. Good thing you can't see the it when it's on the bench.

To secure the fabric to your plywood, we're going to use staples. I used T-50 size staples. Start with one of the long ends of your bench. Fold the edge of the fabric back over on itself about one inch. So that the edge of your fabric is now double thickness. This is the area we're going to staple into, the double thickness ensuring that it won't rip. Put the edge of this fabric onto the top of your plywood. Now begin stapling this edge. Press down hard with your staple gun and start from the middle and work outward. Doing this will allow you to smooth any wrinkles as you go. For the first edge it's not too important because none of the other edges are secured down yet. Staple all along this edge, leave the corners for later, we'll do them at the end.

Ideally, we don't want our pad to be to cushy. We want it to be firm. If you have cushy foam (as most cheap foam is, then we want to compress it by making the fabric sit tight around it. In order to do this, we have to compress the foam by standing on it as you staple. The second side you staple should be the long edge opposite the first side. You don't work around right to left or left to right. When you upholster something like this you work one side, then opposite side. This is the best way to ensure you can keep wrinkles out of the material.

Pull the material as tight as you can. Now trim it down to a size that will fit your bench. Don't trim too much off or it won't fit, but you likely have feet of excess because this bench is not very wide. After you trim it, fold the excess back on itself, just like you did with the first side. Stand on the plywood to compress the foam. Pull everything as tight as you can and begin stapling this edge, again starting from the middle and working out.

Repeat the procedure for the remaining two short ends. Now for the corners. There's no science to this, as far as I know. It's like wrapping a present. It comes out different every time you do it, And it usually looks kinda sloppy. But in the end it gets the job done. That pretty much describes my experience with both gift wrapping and upholstering corners. You'll have to trim some excess material off and probably fold some material in and tuck some things under. Just get it flat enough to put some staples in and it'll be fine.

By my standards, I did quite a sloppy job with the upholstery on this project. But luckily, when it's bolted to the frame the underside is completely hidden. So don't stress out trying to get things perfect, it really doesn't matter. What's important is that your pad is nice and tight and firm.

With the pad done, all that is left is to secure the pad to the frame. Line up your elevator bolts with the holes on your frame and drop it in. Take your wingnuts and hand tighten them onto your bolts. If you choose to paint your bench, do so without the padding on.

Everything you see here for less than $150. I'm assuming you can't see the bar, weights, shoes, and everything else in the back corner.

Now you have a bench that is stronger than you'll ever need it to be. You have the strength and function of an expensive bench and you paid only $50 or less for it. What would you get for $50 if you tried to buy a commercial bench? Something that could barely handle the weight that even a total noob will bench press in a few weeks time. This is the kind of project that makes you love DIY. It's definitely a better way to spend a Saturday than watching TV. Or you could put a TV in the garage and watch while you work.

This was another massive post. If you are unclear about anything please leave a comment and I'll do my best to help you out.

- Carl

62 comments:

  1. Just stumbled on your site. I can't believe I never considered this. I've been looking for a good dumbbell bench for years--and you're right, benches that can handle 400+ lbs are several hundred dollars. I'm definitely doing this, although I may use an additional 2x4 perpendicular to the bench below the head to add additional stability for dumbbell training.

    The other project I'm planning is making my own dumbbell/barbell out of galvanized pipe, like so: http://www.youtube.com/watch?v=spiS9oAQw8w. You should make this project your next feature.

    ReplyDelete
  2. I'd be interested in hearing your thoughts about DIY dumbbells. I'm quitting my gym at the end of the month, and am planning on creating a dumbbell press set up, with a DIY bench, two DIY dumbbell stands, and DIY dumbbells (if possible). I kinda liked the idea of fatbar for everything as a way to force myself to train grip 100% of the time... I'd think I would eventually be able to do that grip for everything. Maybe that's too ambitious. But the main appeal of the pipe was the cost. By the way, I have heard that the outside of a galvanized pipe is a bit under 2", leaving the weights loose enough to spin. Can't confirm that myself, though.
    I own a pair of FatGripz, but I find those make the grip REALLY big--considerably more than 2".

    ReplyDelete
  3. Your big concern is a programming one (training fat bar exclusively). I'm not going to pretend like I'm an expert in that area.

    As far as DIY dumbbells, those shown in the video are not bad and they are inexpensive and super simple. But they are fat bar and they don't have the kind of spin I am talking about (collars or sleeves). I'm not saying that's bad for all situations, it just is what it is.

    I'm sure I'll post an article about DIY dumbbells/barbells in the future, whether I come up with a more complex DIY design or not.

    ReplyDelete
  4. Hey Carl, loving the site. I'm going to try your bench design when I set up my home gym to save some cash for a nicer bar. Thanks for sharing, your plans look much more stable than the sketches I'd made.

    ReplyDelete
  5. Thanks for these plans Carl. I used them as the basis of making my own version http://www.warriortraining.co.uk/2012/01/homemade-weight-bench.html and linked back to your plans here.

    I used 2x6" on some of the uprights simply because I had them laying about from my decking base. Had to improvise a little as they were only 12". Bench is about 18" in total.

    Your design feels solid, and I have no fears getting under the barbell whilst on it.

    Next up is some squat stands unless I can find some cheap on ebay, but if not I will be consulting your plans.

    Keep up the good work Carl.

    ReplyDelete
  6. Nice job. Cleaning up your scrap wood and making a great weight bench is a double whammy of awesomeness.

    ReplyDelete
  7. Carl
    A big thanks for this. Using yours and Scwinners' methods (and a couple of his tools) I've done my own version (largely based on your plans though). Not as pretty but very solid. I've had three adults jump up and down on it with not even a creak. http://www.flickr.com/photos/28688161@N03/6864568079/in/photostream

    ReplyDelete
  8. yes indeed a strongest one and really a nice explanation for this!!!

    ReplyDelete
  9. I made a bench last year, using 6 legs, each leg is 2 inch by 2 inch. Then my wife saw it and is using it as our TV stand.

    So now I have an excuse to have a metal bench welded, also DIY (or hire a welder.)

    ReplyDelete
    Replies
    1. Man, get you and your wife a TV that doesn't require a heavy duty stand. ;) They're made much lighter and thinner these days and can be mounted on a wall.

      Delete
  10. pretty cool, thinking of making a bench myself now
    thanks from the uk.

    ReplyDelete
  11. Do you have any plans/ideas for a shoulder press-type bench (example: http://www.commercial-gym-equipment.co.uk/item360.htm)?

    I have a FID bench and cannot stand how high the bench is for doing shoulder press, overhead triceps exercises, etc. Any thoughts?

    ReplyDelete
    Replies
    1. I get the feeling that there are several solutions to this problem, all of which are easier than building a new bench/chair. Can you elaborate on exactly what the problem is with the FID bench you have? When you say it's too high do you mean the bar in the rack is too low relative to your body seated on the bench? If so I assume the rack is not adjustable. Or do you mean the seat is too high and you are too far off the ground?

      I ask because I don't have any brilliant ideas about how to make a seat that wouldn't be too bulky in my opinion, and I suspect there is a better solution to your problem but I don't know exactly what the problem is.

      Delete
  12. Thanks for the inspiration! I am a draftsman and based on your images and details I have drawn up the bench prior to building it, and I figured I would share the drawing with you and your followers. Bench.pdf

    ReplyDelete
  13. I found your blog while searching for squat stand plans. I built "More than just squat stands", and they're working great! Next I plan to replace the flimsy garage sale bench I've been using with one like yours. One thing I'm not sure I understand, though—why is the head end of the bench wider than the rest? Does the bench need extra strength here, or is it for stability?

    ReplyDelete
    Replies
    1. Thanks. I just finished my bench. I built it entirely of 2x4s, because I had them on hand. All I had to buy was a box of screws for $3.77. I put I-beams at both ends and made the top of 4 2x4s side by side, with no padding. The top is 13.75" wide. Total width of legs is 14". Height 17". Since my workout space is very small, I made it 3 feet long. It only has to support my head, back, and butt, and that's long enough for me. Here's a photo: https://sites.google.com/site/dk54321/weight-bench

      Delete
  14. Thanks for sharing, here are my final results..

    http://postimg.org/image/x3s5h7bzr/

    ReplyDelete
  15. Hey Carl. Couple questions for you. First, though, thanks for posting this and I can't wait to get started on this build!
    1) On your plywood top, you show a 15.5x5" top of the T shape. I can see that the 5" would give you some lip (overhang) on the 4" wide boards, but my calculations show that the top cross part should be 18" (2 I's plus the runner at 2"4"2"2"2"4"2") yet your top part shows a lip at 15.5".
    2) Obviously there won't be any avoiding overhang on the width of the bench where you lay, but would there be any disadvantages to not having a lip anywhere else? IE; making your top plywood exactly 43" long and your top of the T exactly 18x4" (or 15.5x4" if my calculations are crazy. haha)
    Thanks!!

    ReplyDelete
    Replies
    1. Your calculations are off. Because "2x4s" are actually 1.5" x 3.5" once they are processed and in the store. So that would make that top part 14.5" x 3.5". In any case, I can't think of any disadvantage to your suggestion. Keep in mind you do need the overhang along the width of the bench so that you have something to bolt the pad to.

      Delete
    2. Ha! I would have never known until I had it back home and started assembling. Thanks for the foresight. And the quick reply! (Obviously a novice here)

      Delete
  16. For any folks looking to try this out, I just finished mine and have an updated price for you guys of just under $80. Keep in mind, I didn't have any existing materials except staples for this project so everything was bought new. Not a huge deal because this is a great project even for $80, but if you're super budget minded, just be aware. Also, you may be able to shop price better than I. I simply went to Home Depot and grabbed everything one stop except the fabric. Here's my rundown.

    Home Depot:
    2x4x16 $7.59, 2x4x14 $6.30, 3/8"4x8 $13.75, carriage bolts $.68, mach screw $2.36, Gorilla Glue $4.97, Deck screws $6.93, 1/4" drill bit $2.97, 1/8" drill bit $2.97, wood glue $3.97, 4 wingnuts $1.18 TOTAL $56.89 after tax

    Joann Fabrics:
    2.5 yrds 1/2" foam $13.73, .6 yrds black vinyl $6.11, TOTAL 21.03 after tax

    GRAND TOTAL: $77.92

    Thanks for the post, Carl! Looking forward to building the squat rack now!

    ReplyDelete
  17. Thanks for the inspiration. I did it slightly differently with much thicker wood, but less of it. It worked out pretty good. I had all the materials except for the leather so only spent about £12.
    Here is my attempt: http://jcardy.co.uk/super-strong-homemade-weights-bench/

    ReplyDelete
  18. This bench is genious..and your right ive been looking for a flat bench and the only ones under 75 bucks are wobbly and cheap. 200 bucks for a decent flat bench..well this one is well beyond decent, strong as an ox...Thanks...off to build the squat rack/benchpress.

    ReplyDelete
  19. What is in the buckets in the last photo?

    ReplyDelete
    Replies
    1. Latest reply ever but it's concrete. Check out the Squat Stands page for that project.

      Delete
  20. That's incredible. Thanks for the tutorial.

    ReplyDelete
  21. Excellent tutorial. I started mine last night. The only thing I noticed is you can run into trouble with the top box, bottom box measurements since 2x4s are really about 1.5" x3.5". Instead of using 2 and 4 inch measures I'd say go 1.75" and 3.5". Thanks for this great post.

    ReplyDelete
    Replies
    1. You are actually correct here. I'm not sure how I missed that one.

      Delete
  22. I finally finished it. It's a great design, so hats off to you for taking the time to share. The one suggestion I would make is to put a vertical 2x4 at the head and the foot of the bench between the top and bottom long runners to take stress off of the wood screws. The one regret I have is that I didn't treat the wood with an anti-mold agent before I put it together since I'll be using it in a damp garage.

    ReplyDelete
  23. If you are looking for foam, try a carpet store. Ask them if they have any smaller sections of padding they need to get rid of. The place I went to gave it away since they were very small sections of foam (about 14" wide) that were left over from them installing stairs. Just glue a couple layers together to make it the correct thickness.

    ReplyDelete
    Replies
    1. Yeah, you might be able to get the carpet padding for free if you're willing to ask at a specialty store. That being said, it's not expensive even at a big box store. Also you don't have to glue it together. When you upholster it the fabric will hold all the layers in place.

      Delete
  24. This comment has been removed by the author.

    ReplyDelete
  25. This comment has been removed by the author.

    ReplyDelete
  26. I made a Japanese language YouTube video offering my experience and advice on making a bench press using your fine instructions. You can find a link in the description box to a PDF file with a translation of those instructions in Japanese. Your wisdom travels around the world.
    https://www.youtube.com/watch?v=O4bHSx2fnHE

    ReplyDelete
  27. Aloha! I'm wanting to get rid of my "martied old lady" body and get back to feeling like ME! Remodeling my dressing room into a weightroom. This is AWESOME! Thanks!

    ReplyDelete
  28. Did it! Came out really nice. Make sure uf you build this do it on level ground. I put mine together on a uneven surface and it was wobbly when i was done. So i had to spend extra time evening all the 2x4s. All and its sturdy and really comfortable now. Thanks for the plans!

    ReplyDelete
  29. Am I the only one that doesn't see an indication of what plywood to buy??

    ReplyDelete
  30. Great article with diagram. For those diagram, I learn how to make best weight lifting bench

    ReplyDelete
  31. Wonderful article, thanks for putting this together! This is obviously one great post. Thanks for the valuable information and insights you have so provided here.
    BEST WEIGHT BENCH

    ReplyDelete
  32. I just finished building this with the rack set up. Perfect design and great instructions. Total cost after tax is around 140 Can. $ for both. Great value for what you get out of it.

    ReplyDelete
  33. A quick step by step guide. Thanks for sharing here its worth a read Free weight bench series by Nortus Fitness at reasonable price

    ReplyDelete
  34. I love this blog, if you want to maintain good, then you must need weight benches exercise. I found 10 Best Weight Benches at workoutGadget.com. Feel free to check this amazing site.

    ReplyDelete
  35. If you are a health conscious people, then it really important to have effective weight bench. Whenever you are searching about Best Weight Bench Review , then WorkoutGadget.com should come in the first priority.

    ReplyDelete
  36. Thanks For Sharing article which is trully amazing. here are the quick setup guide for Free Weight series

    ReplyDelete
  37. Hey Carl...love this. Do you think there’s a way to make this bench an incline bench also? If I could figure that out, I’d have it all.

    ReplyDelete
  38. Reebok professional deck workout bench
    Then I have determined to write a evaluate on this Reebok Fitness Bench from my experiences with this. I have been the usage of it for two months as properly as Reebok step bench.
    Reebok bench

    ReplyDelete
  39. I love Reebok workout bench for its wonderful features. I've read read amazing review about Reebok Professional Deck Workout Bench here: https://workoutgadget.com/reebok-professional-deck-workout-bench

    ReplyDelete
  40. I haven't read this fully yet but do you think it could be made to hold a thompson fat pad on top?


    I want the pad to be removable so I could leave the wood bench outdoors (and +1 they say the fat pad is easier on your shoulders)

    ReplyDelete
  41. Cheap Gym Equipment, Exercise Machines, Stair Stepper for Sale USA

    Bohgym is a leading company that offers cheap gym equipment, workout / exercise machines, stair climbers, treadmills and stair stepper for sale in the USA.

    ReplyDelete
  42. Update: in 2021, this now costs $35,000 to make.

    ReplyDelete
  43. Nice and informative blog post. Was looking for some important information and visited your this page having crucial and knowledgeable content. Really written well. Share more alike this. Thank you and keep posting.

    ReplyDelete
  44. We Provide Generator on Rent. Sometimes we need a wooden bench so i like this product

    ReplyDelete
  45. you can download video tiktok without watermark free.

    ReplyDelete
  46. Thanks For Sharing article which is fablous. here are the some inportant information for Commercial Gym Equipments

    ReplyDelete